2272 / 1024 / 640 - Start with the right wing.
2272 / 1024 / 640 - Used Robart 1/2A hinges.
2272 / 1024 / 640 - Rubberbands and clip to hold.
2272 / 1024 / 640 - Left wing panel next.
2272 / 1024 / 640 - Four hinges per aileron.
2272 / 1024 / 640 - Perfect!
2272 / 1024 / 640 - Hitec HS-55's in wing.
2272 / 1024 / 640 -
2272 / 1024 / 640 - Hole drilled in stab.
2272 / 1024 / 640 - Weighted down till glue dries.
2272 / 1024 / 640 - Completed. Bottom of stab.
2272 / 1024 / 640 - Cute little hinges.
2272 / 1024 / 640 - Gorilla glued in place.
2272 / 1024 / 640 - Water helps cure.
2272 / 1024 / 640 - Starting to look like a plane!
2272 / 1024 / 640 - Stock rudder, not big enough.
2272 / 1024 / 640 - Add 1" to the back.
2272 / 1024 / 640 - Used one piece of covering.
2272 / 1024 / 640 - Tack down one side.
2272 / 1024 / 640 - Trim excess.
2272 / 1024 / 640 - Other side.
2272 / 1024 / 640 - Trim excess.
2272 / 1024 / 640 - Hard to tell anything modified.
2272 / 1024 / 640 - Hold it up to mark hinges.
2272 / 1024 / 640 - Rubberbands & clip till dry.
2272 / 1024 / 640 - Gorilla glue set.
2272 / 1024 / 640 - Check throws in both directions.
2272 / 1024 / 640 - Power system, w/CC35 controller.
2272 / 1024 / 640 - Carbon Fiber Tissue on Firewall.
2272 / 1024 / 640 - Stiffend it up a lot!
2272 / 1024 / 640 - Stick glued with 30-min epoxy.
2272 / 1024 / 640 - Took out downthrust.
2272 / 1024 / 640 - No need to brace stick now.
2272 / 1024 / 640 - TNT, Smackdown, and stock gear.
2272 / 1024 / 640 - TNT weighs 29 grams.
2272 / 1024 / 640 - Smackdown's just 17 grams.
2272 / 1024 / 640 - Stock wheels and wheelpants.
2272 / 1024 / 640 - Holes pre-drilled in gear.
2272 / 1024 / 640 - Look great!
2272 / 1024 / 640 - Hitec HS-56HB's in the tail.
2272 / 1024 / 640 - Elevator linkage.
2272 / 1024 / 640 - Rudder linkage.
2272 / 1024 / 640 - Castle Creations Phoenix 35
2272 / 1024 / 640 - Install motor.
2272 / 1024 / 640 -
2272 / 1024 / 640 - RX and Battery hold-down.
2272 / 1024 / 640 - Tanic 3S 2150mah Lipo installed.
2272 / 1024 / 640 - Hitec Electron 6 Receiver
2272 / 1024 / 640 - 02/15/2005 - After 1st flight.
2272 / 1024 / 640 - Gearbox broken...
2272 / 1024 / 640 - right at motor screw.
2272 / 1024 / 640 - Razor RZ-2500 + Cobri Gearbox
2272 / 1024 / 640 - Enlarge stick to fit Cobri.
2272 / 1024 / 640 - Original cowl paint too dark.
2272 / 1024 / 640 - Bottom comparison.
2272 / 1024 / 640 - Missing cooling exit hole!!!
2272 / 1024 / 640 - We can fix that!
2272 / 1024 / 640 - Opened up enough for Dremel.
2272 / 1024 / 640 - Sanding wheel modelers best friend!
2272 / 1024 / 640 - Close enough for who it's for.
2272 / 1024 / 640 - Good exit area now!
2272 / 1024 / 640 - Should keep motor cooler.
2272 / 1024 / 640 - Back of motor.
2272 / 1024 / 640 - Change CC35 settings for Razor.
2272 / 1024 / 640 - Ready to go again!
2272 / 1024 / 640 -
2272 / 1024 / 640 - 06/18/2005 - Fix for the gear plate.
2272 / 1024 / 640 - extra basswood and birch 5-ply
2272 / 1024 / 640 - 30 minute epoxy in place.
2272 / 1024 / 640 - Sand a little to keep the lines.
2272 / 1024 / 640 - Pre-cut the replacement Ultracote.
2272 / 1024 / 640 - Lay it on, tack the sides...
2272 / 1024 / 640 - Shrink the rest tight.
2272 / 1024 / 640 - Can't tell it was ever modified!
2272 / 1024 / 640 - Install gear and good to go!
